View RSS Feed

engine46

Cleaned Up My Otto Deutsch Hans With My Dremel, Maas Polish & Mothers Chrome Polish

Rate this Entry
by , 02-21-2015 at 12:44 PM (1048 Views)
Quote Originally Posted by engine46 View Post
Here is how I cleaned up my Otto Deutsch Hans I recently got off eBay. The first pic is what it looked like when I first got it. As you can see the scales looked black & were filthy.
Name:  IMG_7240.jpg
Views: 2379
Size:  39.1 KB
I took it to my kitchen sink where I did the work to it. I did it here so when the blade got warm, I just turned the faucet on & cooled the blade, wiped it off with a dry rag & started polishing again. You can also do this with a glass of water nearby. I usually take the razor apart but this one I didn't, I just carefully worked around the scales. If I leave the scales on I usually put tape on them to protect them but I wanted you to get a better picture of how I did this. I have had several members on here say that they would never use a Dremel on a straight razor but I learned from Lynn's dvd on how to use a Dremel the correct way on a blade. I have not screwed up yet......knock on wood. I cannot stress enough that you must be very careful if using a Dremel on a straight razor or it can be disastrous. You must alway watch which way the tool is spinning or it may grab your blade & crack or chip it. I applied Maas Metal Polish to the blade & went to work with my Dremel. I start polishing.
Name:  IMG_7396.jpg
Views: 260
Size:  56.4 KBName:  IMG_7399.jpg
Views: 263
Size:  46.3 KB
The same method applies to the shoulder except I am polishing perpendicular to the blade but with the polishing wheel spinning away from the blade to prevent any damage when I work my way to the toe as you can see in the photo. I then carefully polish the tang & tail. I also polish the spine as well. If it starts to get warm, it is of course a good idea to cool the blade before you begin again.
Name:  IMG_7400.jpg
Views: 246
Size:  52.3 KBName:  IMG_7401.jpg
Views: 251
Size:  46.5 KBName:  IMG_7406.jpg
Views: 251
Size:  42.6 KBName:  IMG_7409.jpg
Views: 248
Size:  35.3 KB
The next photo is of the name on the scales after just wiping them off with warm soapy water, rinsing & drying them with a dry rag.
Name:  IMG_7414.jpg
Views: 250
Size:  38.4 KB
I then used Mothers Chrome Polish on the outside of the scales. I also used a thin popsicle stick with a rag around it which had some Mothers on it to polish between the scales.
Name:  IMG_7416.jpg
Views: 249
Size:  31.0 KBName:  IMG_7417.jpg
Views: 249
Size:  28.9 KBName:  IMG_7418.jpg
Views: 249
Size:  37.8 KB
There you have it, nicely polished!Name:  IMG_7419.jpg
Views: 250
Size:  47.9 KBName:  IMG_7421.jpg
Views: 253
Size:  27.1 KB
If you look close enough, the scales are translucent instead of the black color they appeared to be at first. The dull spots are glare, not smudge from my fingers. After polishing them, you can barely see the blade through the scales when it is closed. They're dark green as those scales always are!

Updated 02-21-2015 at 01:14 PM by engine46

Categories
Uncategorized

Comments

  1. HARRYWALLY's Avatar
    Excellent blog!
    engine46 likes this.
  2. engine46's Avatar
    Quote Originally Posted by HARRYWALLY
    Excellent blog!
    Thank you very much HARRY. I took a previous post, modified it some & made it into a blog.
  3. Substance's Avatar
    great little write up mate
    engine46 likes this.
  4. Geezer's Avatar
    Nicely done!
    ~Richard
    engine46 likes this.
  5. greatbolo's Avatar
    I'm geting ready to do the same thing - thanks!!
    engine46 likes this.
  6. engine46's Avatar
    Thank you Richard, Substance & great bolo. I greatly appreciate your comments!
  7. engine46's Avatar
    Oh & thank you too Andrew!