Page 11 of 916 FirstFirst ... 7891011121314152161111511 ... LastLast
Results 101 to 110 of 9159
Like Tree39302Likes

Thread: What are you working on?

  1. #101
    Senior Member blabbermouth
    Join Date
    Jan 2011
    Location
    Roseville,Kali
    Posts
    10,432
    Thanked: 2023

    Default

    Really love the color,but I hate working with the material
    Name:  G10 001.jpg
Views: 517
Size:  25.4 KB
    CAUTION
    Dangerous within 1 Mile

  2. #102
    Admin & Forum fixer Bruno's Avatar
    Join Date
    Nov 2006
    Location
    Belgium
    Posts
    13,527
    Thanked: 3803
    Blog Entries
    9

    Default

    Today's work.

    4 razors, made from 1.2842 again.
    All 4 are 8/8. I am getting better at figuring out which order to do things in. For the end result, it doesn't really matter because in the end, everything that is not razor, is gone. But working in the 'right' order makes your work just sooo much easier. I did say they were all 8/8, right? Remember that, because it will be important later on

    Name:  razors_8-8.jpg
Views: 492
Size:  77.9 KB

    After making those 4 razors, I lighted up my forge to heat treat them, and after doing that I forged 2 meat choppers. It's been far too long since I forged anything significant, so I made the classic beginner mistake of using my wrist to hit with the hammer instead of my shoulders and upper arms. After I was halfway through the first, my underarm was numb. It's like swinging a sword. Broad strokes do a lot more than flicks of the wrist.

    In any case, after a lot of sweating and numbness, I ended up with 2 humpback meat choppers with a monkey tail. I used 3/8 thickness. Drawing out the tang was a long chore. I really must practice more. I left enough meat to grind away my rough finish. For that reason, I also always leave the blade an inch too long. I still have some problems with the toe. It always curls up too much, so if I need to forge a chopper, I leave it too long and cut that part off. I also make it too wide so that I have enough meat to create a good edge.

    Atm, they're still a bit too long and wide. Since they are more or less in the right proportion for a big blade, it would be difficult to see just how large they are. That is why I put one of the 8/8 blade in the same picture for reference.

    Yes, they look very rough. That's why I left a lot of meat on them, so give myself room for grinding away the things I don't want.

    Name:  choppers.jpg
Views: 482
Size:  100.4 KB
    Happiness is a field, littered with the mangled corpses of your enemies. - Vlad III of Wallachia

  3. #103
    aka shooter74743 ScottGoodman's Avatar
    Join Date
    Sep 2009
    Location
    SE Oklahoma/NE Texas
    Posts
    6,337
    Thanked: 1427
    Blog Entries
    4

    Default

    Looks like you might get 9/8 out of the bottom and 8/8 out of the forged one on the top. Love the forged ones Bruno & look forward to seeing them transform.
    Northeastern Texas & Southeastern Oklahoma Mentor/Helper...PM me if I can assist you.
    God Bless,
    Scott

  4. #104
    Admin & Forum fixer Bruno's Avatar
    Join Date
    Nov 2006
    Location
    Belgium
    Posts
    13,527
    Thanked: 3803
    Blog Entries
    9

    Default

    Quote Originally Posted by shooter74743 View Post
    Looks like you might get 9/8 out of the bottom and 8/8 out of the forged one on the top. Love the forged ones Bruno & look forward to seeing them transform.
    Actually, the top one is 10/8+ at the narrowest point, and the bottom one is 11/8.
    Granted, the spine isn't exactly smooth so I need to take a bit off ot that too, but I should be able to get 9/8 out of the both of them.
    ScottGoodman likes this.
    Happiness is a field, littered with the mangled corpses of your enemies. - Vlad III of Wallachia

  5. The Following User Says Thank You to Bruno For This Useful Post:

    rocarule (02-16-2014)

  6. #105
    Senior Member blabbermouth Geezer's Avatar
    Join Date
    Jul 2010
    Location
    Menomonie,WI
    Posts
    5,761
    Thanked: 2435
    Blog Entries
    1

    Default

    Got my work cutout for me after a good day scrounging!

    Kropp, Kabeso, Clauss, Genco, Böker, Crow.
    ~Richard
    Last edited by Geezer; 02-15-2014 at 01:57 PM.
    Dratted sell fone.....

  7. #106
    Admin & Forum fixer Bruno's Avatar
    Join Date
    Nov 2006
    Location
    Belgium
    Posts
    13,527
    Thanked: 3803
    Blog Entries
    9

    Default

    Here are the same 2 choppers, but cleaned up a bit, cut to size, and with the lines being more defined.

    The top one is 9/8. Bottom one 10/8

    Name:  chopper_1.jpg
Views: 540
Size:  35.7 KB

    Name:  chopper_2.jpg
Views: 440
Size:  35.4 KB

    Comment from my wife: are those things actually razors?
    Happiness is a field, littered with the mangled corpses of your enemies. - Vlad III of Wallachia

  8. #107
    Senior Member rocarule's Avatar
    Join Date
    Jan 2013
    Location
    Pico Rivera
    Posts
    553
    Thanked: 32

    Default

    those are looking nice bruno. i would love for the tail to be shortened by about 1/4 and the tip to be a bit rounder so long as the blade can be over 2.5"

  9. #108
    aka shooter74743 ScottGoodman's Avatar
    Join Date
    Sep 2009
    Location
    SE Oklahoma/NE Texas
    Posts
    6,337
    Thanked: 1427
    Blog Entries
    4

    Default

    Name:  DSC_0003.jpg
Views: 527
Size:  26.2 KB
    Name:  DSC_0004.jpg
Views: 525
Size:  27.2 KB
    Name:  DSC_0005.jpg
Views: 522
Size:  29.1 KB


    Was trying for a hamon with 1095, it's there, just don't know how well it will look until I get back to the grinder.
    JBHoren, baldy, Geezer and 7 others like this.
    Northeastern Texas & Southeastern Oklahoma Mentor/Helper...PM me if I can assist you.
    God Bless,
    Scott

  10. #109
    Senior Member blabbermouth
    Join Date
    Jan 2011
    Location
    Roseville,Kali
    Posts
    10,432
    Thanked: 2023

    Default

    Do Nothing weekend,doing just dumb Chit stuff,made some handles for some of my files.
    Name:  files 001.jpg
Views: 417
Size:  50.8 KB
    CAUTION
    Dangerous within 1 Mile

  11. #110
    Senior Member
    Join Date
    Oct 2008
    Location
    Tolland, CT
    Posts
    261
    Thanked: 85

    Default

    Here are some of the razors and knives I am currently working on. The knives are 1084, as are two of the razors. The rest of the razors at O-1. They have all been heat treated, but all of the tangs need to be sanded and the blades finish ground. I don't mind the grinding, but I do hate hand sanding!



    Here are a couple of shots of some of the blades being heat treated.



Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •